Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
- 16. The electric equipment
   16.1. Specifications
   16.2. Electric chains
   16.3. Gymnastics system
   16.4. Check of an electric chain of gymnastics
   16.5. Power failure check on a wire connecting the storage battery with the generator
   16.6. Check of the current developed by the generator
   16.7. Check of developed pressure
   16.8. The generator
   16.9. The storage battery
   16.10. Check of relative density of electrolit
   16.11. Gymnastics of the storage battery
   16.12. Survey of the storage battery
   16.13. Start system
   16.14. A starter
   16.15. Check and replacement of elements статора
   16.16. The switch of blocking of ignition
   16.17. Check of the relay of a starter
   16.18. Check of the switch of blocking of ignition
   16.19. A radio receiver
   16.20. Dynamics
   16.21. The aerial
   16.22. The multipurpose switch
   16.23. A sound signal
   16.24. Safety locks
   16.25. A combination of devices
   16.26. The engine of a screen wiper of a windscreen
   16.27. Replacement of a headlight and the forward index of turn
   16.28. Adjustment of light of headlights
+ 17. The appendix
+ 18. Electroschemes




16.22. The multipurpose switch


Removal and installation

Cars without a safety pillow

PERFORMANCE ORDER
1. Remove the button of a sound signal and a steering wheel.
2. Remove the top and bottom casings of a steering column.
3. Turn out screws and remove the multipurpose switch.
4. Installation is spent to sequences, return to removal.

Cars with a safety pillow

At removal of the multipurpose switch on the cars equipped with a pillow of safety, be cautious and satisfy following conditions.
The prevention

Do not assort any of components of auxiliary system of safety SRS. Dismantling of components can put safety system out of action.
Exclude hit on a pillow of safety of solvents or clearing substances.
Transport a safety air cushion separately, a bag upwards.
If any component SRS has fallen or on it there are cracks, dents or other defects in the case, an arm or a socket, replace them with the new.
At transportation do not place a hand on a safety pillow.
Do not heat up the block of a pillow of safety to temperatures above 93°C.
After expansion of a pillow of safety replace a spiral spring of the gauge with the new.
Before installation of a spiral spring of the gauge of a pillow of safety combine a label and the index of neutral position of a spring of the gauge, preliminary having established forward wheels for movement it is direct forward. If the label of a spiral spring is not combined properly, the steering wheel cannot turn completely or the wire of a spiral spring will be damaged, complicating normal work SRS.


PERFORMANCE ORDER
1. Disconnect a wire from the negative plug of the storage battery.

The prevention

Before service of system of pillows of safety be convinced, that has passed not less than 30 with the ambassador of deenergizing of ignition and a detachment of a wire from the negative plug of the storage battery.
The system of pillows of safety is equipped by an emergency energy source which allows to develop pillows of safety in case of a detachment of wires from the storage battery at failure.


2. Turn out bolts of fastening of a pillow of safety. Disconnect sockets of a sound signal and a pillow of safety and remove the block of a pillow of safety.
3. Remove a steering wheel.
4. Remove an emphasis for knees of the driver.
5. Turn out screws and remove the top and bottom casings of a steering column.
6. Turn out screws and remove the multipurpose switch.
7. Installation is spent to sequences, return to removal.

Check

With the multipurpose switch in each position check up conductivity between corresponding contacts of sockets. If conductivity mismatches demanded, replace the multipurpose switch.

The illumination switch (socket M10–2)

The switch of light of headlights (socket M10–2)

HU: a headlight of headlights
HL: a passing light of headlights
P: dimensional illumination

The turn switch (socket M10–2)

The screen wiper switch (socket M10–1)

The switch стеклоомывателя (socket M10–1)