Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
- 2. The engine
   - 2.1. Engines SOHC
      2.1.1. Specifications
      2.1.2. A gear belt
      2.1.3. Check of a tension of a gear belt
      2.1.4. Adjustment of a tension of a gear belt
      2.1.5. Поликлиновой a belt
      2.1.6. Engine support
      2.1.7. A forward cover and the oil pump
      2.1.8. The air filter (ACL)
      2.1.9. A head of cylinders
      2.1.10. Коромысла
      2.1.11. Hydraulic jacks of backlashes of valves
      2.1.12. Replacement of a saddle of the valve
      2.1.13. Replacement of the directing plug of the valve
      2.1.14. The valve
      2.1.15. A camshaft
      2.1.16. Rods
      2.1.17. A cranked shaft
      2.1.18. A flywheel
      2.1.19. A piston finger
      2.1.20. A final collector
      2.1.21. An inlet collector and the air chamber
      2.1.22. The block of cylinders
      2.1.23. Removal and engine and transmission installation
      2.1.24. System of release of the fulfilled gases
      2.1.25. Search and elimination of malfunctions
   + 2.2. Engines DOHC
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes




2.1.22. The block of cylinders

Forward arm of the block of cylinders of engine SOHC


Dismantling

PERFORMANCE ORDER
1. Remove a head of cylinders, a gear belt, a forward cover, a flywheel, pistons and a cranked shaft.
2. The special adaptation (09260-32000) turn out the gauge of pressure of oil.

Check

PERFORMANCE ORDER
1. Remove from the block of cylinders of the engine the rests of linings, hermetic, a dirt, oil, lubricant and other alien materials. Visually check up the block of cylinders on absence of a rust, corrosion, cracks or any other defects.
2. Clear interfaced surfaces of a head of the block of cylinders and the block of cylinders of the lining rests. A metal ruler and щупом in six directions check up planeness of an interfaced surface of the block of cylinders.

Deviation from planeness: 0,05 mm
The maximum deviation from planeness: 0,1 mm

3. Measure diameters of cylinders in opposite directions, in three planes on height of cylinders. If diameters of cylinders exceed admissible values, have ovality or конусность or the surface of cylinders is damaged or has development, the block of cylinders it is necessary to chisel and establish new pistons and piston rings of the repair size.

Nominal diameter of the cylinder: 75,5 mm
Конусность the cylinder: no more than 0,02 mm

4. If in the top part of the cylinder there is a step, cut off its special tool.
5. As spare parts pistons of four increased sizes are delivered: 0,25, 0,5, 0,75 and 1,00 mm.
6. At расточке cylinders till next increased size, sustain a backlash between the piston and the cylinder and be convinced, that pistons have the same increased size.

Measure external diameter of each piston a sort by a corner 90 ° to a piston finger, on distance of 12 mm from a piston skirt.

Backlash between the piston and the cylinder: 0,025-0,045 mm