Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
- 10. Axes and power shafts
   10.1. Specifications
   10.2. A power shaft
   10.3. A power shaft with SHRUS ball and Birfield type
   10.4. A power shaft with SHRUS Birfield and трипоидного type
   10.5. A rotary fist and a nave of a forward wheel
   10.6. A back axis
   10.7. Search and elimination of malfunctions
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

10.5. A rotary fist and a nave of a forward wheel

1 – the bearing;
2 – a nut, 73–90 Н•м;
3 – a rack;
4 – a rotary fist;
5 – a tip of steering draught;
6 – a nut, 15–34 Н•м;
7 – a nave of a forward wheel;

8 – a brake disk;
9 – a nut, 220–260 Н•м;
10 – a brake board;
11 – a nut, 60–72 Н•м;
12 – a bolt, 65–75 Н•м;
13 – a lock spring ring.

Removal

PERFORMANCE ORDER

1. Lift the car and remove a forward wheel.
2. Turn out a nut of fastening of a power shaft.
3. Remove a support and a soft wire fix it on a forward rack.
4. Remove the gauge of frequency of rotation from a rotary fist.
	5. Take шплинт and turn away a nut of fastening of a pin of the spherical hinge of a tip of steering bent for to a rotary fist. A stripper 09568–34000 squeeze out a pin of the spherical hinge from a rotary fist.
	6. Note position and turn out bolts of fastening of the bottom part of a rack of a forward suspension bracket to a rotary fist.
7. A kapron hammer beat out a power shaft from a nave of a forward wheel. If the power shaft densely sits in a nave of a forward wheel, spray пропиточный aerosol solvent on area шлицов and then repeatedly screw a nut with a fillet so that it settled down flush with a shaft end face. Striking on a nut a brass hammer, beat out a power shaft from a nave.
	8. A stripper 09568–34000 disconnect the spherical hinge of the bottom lever from a rotary fist.
9. Remove a rotary fist together with a nave of a forward wheel.
10. Installation is spent to sequences, return to removal.

Dismantling

PERFORMANCE ORDER

1. Remove a brake disk from a nave of a forward wheel.
	2. Remove a lock spring ring.
	3. Establish special tools, as is shown in drawing.
4. Turning the special tool, remove a nave of a forward wheel from a rotary fist.
5. Remove the special tool and a dustproof ring.
	6. The special tool remove an internal ring of the bearing from a nave.
	7. The special tool remove an external ring of the bearing from a rotary fist.

Check

PERFORMANCE ORDER

1. Check up a nave on absence of cracks and deterioration.

2. Check up a brake disk on absence of development and damages.

3. Check up the hinge on absence of cracks.

4. Check up a spring ring on absence of cracks or damages.

Assemblage

PERFORMANCE ORDER

1. Apply a thin film консистентной greasings in an aperture of a rotary fist and on an external ring of the bearing.
	2. A press with оправкой the corresponding diameter запрессуйте the new bearing of a wheel.
The prevention Do not make effort of a press an internal ring of the bearing.
3. Establish a dustproof ring.
4. A press with оправкой the corresponding diameter запрессуйте a nave in the wheel bearing.
	The prevention Do not make effort of a press an external ring of the bearing.
5. Establish a brake disk.
	6. The special tool tighten a nave to a rotary fist, having tightened a bolt of the adaptation the moment 240 Н•м.
7. Some times turn a nave that bearing elements were established on the places.
8. Measure twisting moment which is necessary for putting for проворачивания the bearing. The twisting moment: 1,3 Н•м
	9. If twisting moment 0 Н•м, measure axial люфт the nave bearing.
	10. If the twisting moment exceeds demanded value, means, the bearing is incorrectly established in a rotary fist and on a nave. Disassemble a rotary fist and repeatedly collect it. Axial люфт the bearing: 0,08 mm
11. Remove the special tool.

home