Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
- 2. The engine
   + 2.1. Engines SOHC
   - 2.2. Engines DOHC
      2.2.1. Specifications
      2.2.2. Compression check
      2.2.3. A gear belt
      2.2.4. Поликлиновой a belt
      2.2.5. Engine support
      2.2.6. A forward cover
      2.2.7. The air filter (ACL)
      2.2.8. A head of cylinders
      2.2.9. Camshafts
      2.2.10. Replacement of a saddle of the valve
      2.2.11. Replacement of the directing plug of the valve
      2.2.12. The valve
      2.2.13. Rods
      2.2.14. A cranked shaft
      2.2.15. A flywheel
      2.2.16. The piston
      2.2.17. A final collector
      2.2.18. An inlet collector and the air chamber
      2.2.19. The block of cylinders
      2.2.20. Removal and engine and transmission installation
      2.2.21. System of release of the fulfilled gases
      2.2.22. Search and elimination of malfunctions
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

2.2.6. A forward cover

1 – the mesh oil filter;
2 – a bolt, 15-22 Н•м;
3 – a lining;
4 – a stopper;
5 – a spring;
6 – a bolt, 20-27 Н•м;
7 – a forward sealing ring;
8 – a forward cover;
9 – an internal gear wheel of the oil pump;

10 – an external gear wheel of the oil pump;
11 – a cover of the oil pump;
12 – a lining;
13 – a bolt, 6-8 Н•м;
14 – the oil pallet;
15 – a lining;
16 – a stopper, 35-45 Н•м;
17 – плунжер;
18 – the oil filter.

The prevention

At stopper installation it is necessary to use a new sealing ring.

Removal

PERFORMANCE ORDER

1. Remove a gear belt.
2. Turn out all bolts of fastening of the oil pallet.
3. Remove the oil pallet.
4. Remove the oil filter.
5. Remove a forward cover from the block of cylinders.
6. Remove a cover of the oil pump.
	7. Remove internal and external gear wheels of the oil pump from a forward cover, preliminary having noted their mutual position.
8. Turn out a stopper and remove a spring and плунжер.

Check

PERFORMANCE ORDER

1. Check up a forward cover on absence of cracks or damages and if necessary replace it.
2. Check up a forward sealing ring on absence of deterioration or damage of working edges and if necessary replace it.
3. Check up a condition of the oil pallet and if necessary replace it.
4. Check up the mesh oil filter on absence of damages and if necessary replace it.
5. Check up a forward cover on absence of deterioration or damages to places of contact to gear wheels of the oil pump and if necessary replace it.
6. Check up a condition of the safety valve established in a forward cover.
7. Check up the form and absence of damages of a spring of a safety valve. Length of a spring a free condition: 46,6 mm Length under loading: 6,1 kg / of 40,1 mm

Installation of a forward cover

PERFORMANCE ORDER

Establish a forward cover with a new lining and fix bolts, having tightened their demanded moment.

Length of bolts: And – 22 mm; In – 30 mm; With – 45 mm; D – 60 mm; the inhaling moment – 12–15 Н•м

Forward oil sealing ring

PERFORMANCE ORDER

1. Check up a forward sealing ring on absence of deterioration or damage of working edges and if necessary replace it.
2. Check up a condition of the spring ring which are pressing out working edges of a sealing ring.
3. At installation use a new sealing ring.
	4. Grease an external surface of a new sealing ring with engine oil. The special tool 09231–22100 or the plug of the corresponding diameter establish a sealing ring on a cranked shaft to a contact of a forward cover.
	5. The special tool 09231–22000 establish a sealing ring against the stop in a nest of a forward cover.
6. Establish a pulley of a cranked shaft, a gear belt and a pulley of a cranked shaft.
7. Establish the oil filter.
8. Clear of the rests of an old lining interfaced surfaces of the oil pallet and the block of cylinders.
	9. Put a continuous layer of hermetic in diameter of 4 mm on an interfaced surface of the oil pallet. Round apertures for bolts hermetic have from the inside. After hermetic drawing it is necessary to establish the pallet no more than in 15 minutes
10. Establish the oil pallet on the block of cylinders and fix bolts. The inhaling moments: 6–8 Н•м

home