Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
- 14. A body
   14.1. Specifications
   14.2. Adjustment of hinges of a cowl
   14.3. A luggage carrier cover
   14.4. Adjustment of a door of a luggage space
   14.5. A forward door
   14.6. A back door
   14.7. Молдинги
   14.8. The roof hatch
   14.9. An external rear-view mirror
   14.10. The central console
   14.11. The panel of devices
   14.12. Ceiling furnish
   14.13. A back shelf
   14.14. A luggage carrier upholstery
   14.15. An internal upholstery of salon
   14.16. A windscreen
   14.17. Back glass
   14.18. A forward bumper
   14.19. A back bumper
   14.20. A back seat
   14.21. A forward seat
   14.22. Search and elimination of malfunctions
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

14.16. A windscreen

1 – распорная the windscreen plug;
2 – молдинг a windscreen;
3 – an internal rear-view mirror;

4 – a windscreen;
5 – a windscreen lining.

Removal

PERFORMANCE ORDER

	1. Before windscreen removal remove following elements: - The top upholstery of a forward rack; - Internal rear-view mirror; - Screen wiper levers; - Overlay of the top part of a cowl; - молдинг a windscreen.
	2. The special tool 09861-31100 cut hermetic of fastening of a windscreen.
	3. If glass is repeatedly established, leave a hermetic layer on glass and a body. Note glass position on a car body.
	4. The special tool 09861-31400 remove a windscreen from the car.

Installation

PERFORMANCE ORDER

	1. The special tool or a knife cut off old hermetic till a thickness of a layer of 2 mm on all perimetre of a framework and a windscreen.
The prevention Be cautious not to remove some hermetic more than it is necessary, and also not to damage a paint and varnish covering of the car.
2. Degrease the processed surface.
	3. Put a windscreen to a window aperture and in four points on a body note glass installation sites.
	4. Paste a rubber lining to an internal surface of a windscreen. Height of a layer of hermetic: Above: 13,5 mm From sides: 13,5 mm From below: 27 mm
	5. Establish a windscreen.
	6. Apply a thin film a glass first coat on an outer side of a rubber lining of a windscreen.
The prevention Do not concern a layer of hermetic with a hand. In a place of a contact of hermetic it cannot provide with a hand reliable connection and in this place leaks after glass installation are possible. Do not put on glass a first coat intended for a body.
	7. Apply a thin film first coats on originally put hermetic acting on perimetre of glass. Glass is necessary for establishing during 10 mines after first coat drawing.
8. Put in pawn glue in a syringe and put it on windscreen edge.
The prevention Put glue during 5 mines after drawing of a glass first coat.
9. The special tool or suckers establish glass over a window aperture according to earlier put labels and press glass to a window aperture.
	10. Шпателем remove superfluous glue. Fill all bowls and emptiness on windscreen perimetre.
11. Directing a water stream on a windscreen, check up tightness of its installation. Do not direct on fresh hermetic a water stream under the big pressure.
	12. In the presence of leaks dry up the damaged area and put hermetic.
The prevention Do not maintain the car within 4 hours after glass installation. After windscreen installation support it within the first hour.
	13. Establish into place all earlier removed elements.
The prevention Within 2-3 days after installation of a windscreen do not clap doors. Avoid movement on rough roads where the car body is exposed to intensive twisting.

home