Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
- 14. A body
   14.1. Specifications
   14.2. Adjustment of hinges of a cowl
   14.3. A luggage carrier cover
   14.4. Adjustment of a door of a luggage space
   14.5. A forward door
   14.6. A back door
   14.7. Молдинги
   14.8. The roof hatch
   14.9. An external rear-view mirror
   14.10. The central console
   14.11. The panel of devices
   14.12. Ceiling furnish
   14.13. A back shelf
   14.14. A luggage carrier upholstery
   14.15. An internal upholstery of salon
   14.16. A windscreen
   14.17. Back glass
   14.18. A forward bumper
   14.19. A back bumper
   14.20. A back seat
   14.21. A forward seat
   14.22. Search and elimination of malfunctions
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes







14.17. Back glass

1 – молдинг back glass;
2 – a lining of back glass;
3 – top молдинг back glass;
4 – back glass;
5 – the bottom lining of back glass;
6 – молдинг back glass;
7 – a lining of back glass;
8 – back glass.

Removal

PERFORMANCE ORDER
1. Before windscreen removal remove following elements:

– Disconnect a socket from a heater of back glass;
– The top upholstery of a back rack;
– A bolt of fastening of the top part of a back seat belt;
– A back shelf.
2. Remove back glass in the same way, as well as a windscreen.

Installation

PERFORMANCE ORDER
1. The special tool or a knife cut off old hermetic till a thickness of a layer of 2 mm on all perimetre of a framework and back glass.

The prevention

Be cautious not to remove some hermetic more than it is necessary, and also not to damage a paint and varnish covering of the car.


2. Degrease the processed surface.
3. Put back glass to a window aperture and in four points on a body note glass installation sites.
4. Paste a rubber lining to an internal surface of back glass.

Height of a layer of hermetic
"In" – four-door cars:
Above: 13,5 mm
From sides: 13,5 mm
From below: 27 mm
"With" – three - five-door cars:
Above: 23 mm
From sides: 23 mm
From below: 42 mm

5. Establish молдинг on back glass.
6. Apply a thin film a glass first coat on an outer side of a rubber lining of back glass.

The prevention

Do not concern a layer of hermetic with a hand.
In a place of a contact of hermetic it cannot provide with a hand reliable connection and in this place leaks after glass installation are possible.
Do not put on glass a first coat intended for a body.


7. Apply a thin film first coats on originally put hermetic acting on perimetre of glass. Glass is necessary for establishing during 10 mines after first coat drawing.
8. Put in pawn glue in a syringe and put it on edge of back glass.

The prevention

Put glue during 5 mines after drawing of a glass first coat.


9. The special tool or suckers establish glass over a window aperture according to earlier put labels and press glass to a window aperture.
10. Шпателем remove superfluous glue. Fill all bowls and emptiness on perimetre of back glass.
11. Directing a water stream on back glass, check up tightness of its installation. Do not direct on fresh hermetic a water stream under the big pressure.
12. In the presence of leaks dry up the damaged area and put hermetic.

The prevention

Do not maintain the car within 4 hours after glass installation.
After installation of back glass support it within the first hour.


13. Establish into place all earlier removed elements.

The prevention

Within 2–3 days after installation of back glass do not clap doors.
Avoid movement on rough roads where the car body is exposed to intensive twisting.