Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
- 11. A suspension bracket
   11.1. Specifications
   11.2. The bottom lever of a forward suspension bracket
   11.3. Replacement of the plug of the bottom lever
   11.4. Plug replacement (G) the bottom lever
   11.5. The forward stabilizer of cross-section stability
   11.6. A rack of a back suspension bracket
   11.7. Replacement of the plug of the back longitudinal lever of a back suspension bracket
   11.8. Replacement of the plug of the back cross-section lever (And and) a back suspension bracket
   11.9. The back stabilizer of cross-section stability
   11.10. Corners of installation of forward wheels
   11.11. Adjustment of a convergence of back wheels
   11.12. Deterioration of tyres
   11.13. Chains противоскольжения
   11.14. Wheel palpation
   11.15. A tightening of nuts of fastening of a wheel
   11.16. Shift of wheels
   11.17. Check of withdrawal and course instability of the car
   11.18. Care of disks from an aluminium alloy
   11.19. Search and elimination of malfunctions
   11.20. Diagnostics of deterioration of tyres
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes




11.10. Corners of installation of forward wheels

Check of corners of installation of forward wheels is necessary for spending at the special stand, thus the car should be in horizontal position with the forward wheels established for rectilinear movement. Be preliminary convinced, that the forward suspension bracket and a steering are in a normal condition, tyres and wheels have no defects.

Convergence

The convergence is defined as a difference of distances (В–А) between forward and back boards of rims of wheels. The positive convergence means, that wheels are in front located is more close to each other, than behind, at measurement at height of an average point of a wheel. If the convergence mismatches demanded value, ослабьте the left and right counternuts of tips of steering draughts, then, rotating draughts, establish demanded corners. Tighten counternuts. Turn on S a turn of connecting draughts changes a positive convergence approximately to 5,5 mm.

Convergence: 0±3 mm

The prevention

Convergence adjustment should be carried out by rotation of the left and right tip of steering draught on an identical corner.
At convergence adjustment ослабьте an external collar of fastening of a protective cover to prevent its twisting.
After adjustment tighten counternuts of tips of steering draughts and collars of fastening of covers.


The moment of an inhaling of counternuts: 50–55 Н•м

Disorder

Disorder is a corner of an inclination of a wheel in relation to a road covering in a vertical plane. It can be positive if wheels are inclined outside, or negative if wheels are inclined inside. The disorder corner, basically, influences cross-section forces.

Disorder: 0°± 30 '

Corner of a longitudinal inclination шкворня

The corner of a longitudinal inclination шкворня is established at manufacturing of the car and cannot be regulated. If the corner of a longitudinal inclination шкворня mismatches demanded values, replace погнутые or the damaged details.

Corner of a longitudinal inclination шкворня: 1°48 ' ±30 '

The prevention

Before check and adjustment of corners of installation of wheels the forward suspension bracket should be free from the worn out, free or damaged details.
Adjustment of corners of installation of wheels is necessary for spending, using the special tool 09529–21000.
Disorder and corner of a longitudinal inclination шкворня are established at manufacturing of the car and cannot be regulated.
If disorder and a corner of a longitudinal inclination шкворня mismatch demanded values, replace погнутые or the damaged details.