Hyundai Accent

Repair and car operation



Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
- 11. A suspension bracket
   11.1. Specifications
   11.2. The bottom lever of a forward suspension bracket
   11.3. Replacement of the plug of the bottom lever
   11.4. Plug replacement (G) the bottom lever
   11.5. The forward stabilizer of cross-section stability
   11.6. A rack of a back suspension bracket
   11.7. Replacement of the plug of the back longitudinal lever of a back suspension bracket
   11.8. Replacement of the plug of the back cross-section lever (And and) a back suspension bracket
   11.9. The back stabilizer of cross-section stability
   11.10. Corners of installation of forward wheels
   11.11. Adjustment of a convergence of back wheels
   11.12. Deterioration of tyres
   11.13. Chains противоскольжения
   11.14. Wheel palpation
   11.15. A tightening of nuts of fastening of a wheel
   11.16. Shift of wheels
   11.17. Check of withdrawal and course instability of the car
   11.18. Care of disks from an aluminium alloy
   11.19. Search and elimination of malfunctions
   11.20. Diagnostics of deterioration of tyres
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. A central air
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes




11.2. The bottom lever of a forward suspension bracket

1 – a nut, 35–45 Н•м;
2 – a nut, 35–45 Н•м;
3 – a nut, 45–60 Н•м;
4 – a back support of the engine;
5 – a bolt, 30–40 Н•м;
6 – the stabilizer of cross-section stability;
7 – the bottom frame;
8 – a bolt, 95–120 Н•м;
9 – a bolt, 95–120 Н•м;
10 – the bottom lever of a forward suspension bracket;
11 – a nut, 60–72 Н•м.

Removal

PERFORMANCE ORDER
1. Remove a forward wheel.
2. Get шплинт from a power shaft, turn away a nut and remove a washer of fastening of a power shaft to a nave of a forward wheel.
3. Ослабьте a nut of fastening of the spherical hinge of the bottom lever, but do not turn out it completely.
4. Turn out two bolts of fastening of the bottom part of a rack to a rotary fist.
5. Removing outside a rotary fist, get a power shaft from a nave.
6. A stripper 09568–34000 squeeze out a pin of the spherical hinge from a rotary fist.
7. Temporarily establish the bottom bolt of fastening of a rack of a forward suspension bracket.
8. Turn out a nut of fastening of draught of the stabilizer.
9. Turn out a bolt of fastening of the forward party of the bottom lever and back bolts of fastening of the plug.
10. Remove the bottom lever.

Installation

PERFORMANCE ORDER
Fix draught of the stabilizer a wrench with an open pharynx on 14 mm and screw самоконтрящуюся a nut.

Dismantling

Replacement of the spherical hinge and dustproof cover

PERFORMANCE ORDER
1. A screw-driver edge remove a dustproof cover from the spherical hinge of the bottom lever.
2. Remove a spring ring.
3. A kapron hammer separate the spherical hinge from the bottom lever.
4. The special tool запрессуйте the new spherical hinge in the bottom lever.
5. Establish a spring ring.
6. The special tool establish a dustproof cover.