Hyundai Accent

Repair and car operation

Hyundai Accent
+ 1. The maintenance instruction
+ 2. The engine
+ 3. Greasing system
+ 4. Cooling system
+ 5. The control, toxicity decrease
+ 6. Fuel system
+ 7. Ignition system
+ 8. Coupling
+ 9. A transmission
+ 10. Axes and power shafts
+ 11. A suspension bracket
+ 12. A steering
+ 13. Brake system
+ 14. A body
- 15. A central air
   15.1. Specifications
   15.2. The instruction on coolant application
   15.3. Remarks at replacement of elements of a central air of air
   15.4. Connection of elements of a central air of air
   15.5. Check of elements of the central air established on the car
   15.6. Installation of manometres for pressure measurement
   15.7. Откачка atmospheric air from a central air
   15.8. Gymnastics of a central air of air
   15.9. Check of level of a coolant
   15.10. Check of operational characteristics
   15.11. Oil for greasing of the compressor of the conditioner
   15.12. Relay check
   15.13. The conditioner compressor
   15.14. The plug of coupling and a pulley of the compressor of the conditioner
   15.15. The coil of excitation of coupling
   15.16. Compressor check on the car
   15.17. The gauge of threefold (double) pressure
   15.18. The fan and the condenser
   15.19. The evaporator
   15.20. Check of the thermostatic gauge (термистора)
   15.21. The air filter of the evaporator
   15.22. The heating and ventilation block
   15.23. The heater block
   15.24. The fan
   15.25. Search and elimination of malfunctions
+ 16. The electric equipment
+ 17. The appendix
+ 18. Electroschemes

15.14. The plug of coupling and a pulley of the compressor of the conditioner

Coupling and pulley of the compressor of the conditioner

1 – распорная the plug;
2 – a pulley and the bearing;
3 – the excitation coil;
4 – a socket electromagnetic муфты;
5 – a sealing ring;
6 – knot of pipelines;
7 – a bolt, 16,3–26,6 Н•м;
8 – a plate;

9 – the conditioner compressor;
10 – shaft consolidation;
11 – a sealing ring;
12 – consolidation;
13 – a lock ring;
14 – a disk and the plug;
15 – a bolt, 10,2–15,3 Н•м.

Removal

PERFORMANCE ORDER

	1. Turn out a bolt of fastening of the plug of the coupling, thus a special key 09977–34000 keep the plug from проворачивания.
	2. Remove the plug of coupling and a lining from a compressor shaft. If the plug does not act in film, screw a bolt on М8 in an aperture of a shaft of the plug and for a bolt remove the plug.
	3. Remove a lock ring.
4. Remove a pulley and the bearing from a compressor shaft.

Installation

PERFORMANCE ORDER

1. Clear a working surface of the bearing of a pulley of the compressor and remove dirt and corrosion traces.
	2. Establish a pulley and the bearing on a compressor shaft.
	3. Establish a lock ring.
	4. Arrange one lining распорной plugs of a nominal thickness in a flute of the plug and establish the plug on a compressor shaft.
	5. Establish the new plug and fix its bolt, having tightened its demanded moment. The inhaling moment: 10,2–15,3 Н•м
The prevention Do not use pneumatic tools.
	6. Щупом check up a backlash of coupling of the compressor of the conditioner between the plug of coupling and a pulley. Check up a backlash in three points on pulley perimetre. Backlash: 0,35–0,75 mm
7. If the backlash differs from demanded, adjust it, having established a lining of a corresponding thickness.

home